There’s only so much room on these two
pages, so check it all out in our new virtual electronic catalog! Flip through the
pages and search with ease! Visit
Follow Us and SAVE
Follow us on your favorite network site and
look for a lot of super deals posted frequently...
exclusively for our followers!
HV Plasma Generator
Generate 2” sparks to a handheld
screwdriver! Light fluorescent tubes
without wires! This plasma generator creates up to 25kV at 20kHz from a
solid state circuit! Build plasma bulbs from
regular bulbs and more! Runs on 16VAC or 5-24VDC.
PG13 HV Plasma Generator Kit $64.95
Signal Magnet Antenna
The impossible AM radio antenna that pulls in the stations and
removes the noise, interference,
and static crashes from your radio! Also
helps that pesky HD AM Radio stay
locked! Also available factory assembled.
SM100 Signal Magnet Antenna Kit $89.95
Air Blasting Ion Generator
Generates negative ions along with a
hefty blast of fresh air, all without any
noise! The steady state DC voltage
generates 7.5kV DC negative at 400uA,
and that’s LOTS of ions! Includes 7 wind
tubes for max air! Runs on 12-15VDC.
IG7 Ion Generator Kit $64.95
Active Receive Antenna
The popular antenna for the serious
DX’ers works on all bands - shortwave,
HF, VHF, and UHF yet performs like a
60’ long wire antenna! Provides over
15dB of gain, and includes auto-off
RF bypass and front panel gain control.
AA7C Active Antenna Kit $59.95
Broadband RF Preamp
Need to “perk-up” your counter or
other equipment to read weak signals? This preamp has low noise and
yet provides 25dB gain from 1MHz to well
over 1GHz. Output can reach 100m W! Runs on
12 volts AC or DC or the included 110VAC PS. Assmb.
PR2 Broadband RF Preamp $69.95
Passive Aircraft Monitor
The hit of the decade! Our patented receiver hears the entire aircraft band without any
tuning! Passive design has no LO, therefore
can be used on board aircraft! Perfect for
airshows, hears the active traffic as it happens! Available kit or factory assembled.
ABM1 Passive Aircraft Receiver Kit $89.95
Tunable AM Radio Transmitter
The AM1 is a great first kit and a fine
low power AM broadcaster for
the hobbyist on a budget. It’s
a great way to learn the basics
of AM broadcast technology,
not to mention basic soldering
and component identification (if
you’re a beginner!). The transmitter can be
tuned to broadcast anywhere in the AM band (550 to
1600 kHz). Setting frequency is simple.
With 100 m W of output power, range can be up to ¼
mile. Connect any line level audio source from your
CD player, tape deck, or mic mixer to the RCA input on
the rear panel of the AM1C and you’ll be on the air.
It’s that simple!
Laser Trip Sensor Alarm
AM1C Tunable AM Radio Xmtr Kit $34.95
True laser protects over 500
yards! At last within the
reach of the hobbyist, this neat kit uses a standard
laser pointer (included) to provide both audible and
visual alert of a broken path. 5A relay makes it simple
to interface! Breakaway board to separate sections.
Audio Recorder & Player
K8094 Audio Recorder/Player Kit $32.95
Record and playback up to 8 minutes of
messages from this little board! Built-in
condenser mic plus line input, line &
speaker outputs. Adjustable sample rate
for recording quality. 4-switch operation that can be
remote controlled! Runs on 9-12VDC at 500mA.
Collinear Vertical FM Antenna
Our 5/8 wave omni antenna has been the
standard for LPFM insallations worldwide.
Provides 3.4dB gain while keeping the signal radiation low to the horizon for maximum range. Field tuneable over the entire FM range
for a perfect match. SO239 connector for PL259 plug.
FMA200E Omnidirectional FM Antenna $119.95
Logic Interface Module
RI1 Logic Interface Kit $17.95
Interface your digital output to the
real world with an on-board SPDT
relay rated at 240V at 10A! It takes a digital
low (.5VDC or less) or a high (+1 to +12VDC) and
provides your choice of an active low or high closure!
It’s that simple! Runs on 12VDC at 60mA.
Digital Voice Changer
MK171 Digital Voice Changer Kit $14.95
This voice changer kit is a riot!
Just like the expensive units you
hear the DJ’s use, it changes your voice
with a multitude of effects! Features a
built-in microphone and both a speaker and line output. Runs on a standard 9V battery, not included.
The true professional workhorse of our FM Stereo transmitter line, the FM100B has
become the transmitter of choice for both amateurs and professionals around the world. From the
serious hobbyist to churches, drive-in theaters, colleges and schools, it continues to be the leader. Not just a
transmitter, the FM100B is a fully functional radio station and provides everything but the audio input and antenna system! Just add that and you’re on the air!
This professional synthesized transmitter is adjustable directly from the front panel with a large LED digital readout of the operating frequency. Just enter the setup mode and set your frequency. Once selected and locked
you are assured of a rock stable carrier with zero drift. The power output is continuously adjustable throughout
the power range of the model selected. In addition, a new layer of anti-static protection for the final RF amplifier stage and audio inputs has been added to protect you from sudden static and power surges.
Audio quality is equally impressive. A precision active low-pass brick wall audio filter and peak level limiters give
your signal maximum "punch" while preventing overmodulation. Two sets of rear panel stereo line level
inputs are provided with front panel level control for both. Standard unbalanced “RCA” line inputs
are used to make it simple to connect to the audio output of your computer, MP3 player, DVD
player, cassette deck or any other consumer audio source. Get even more creative and use
our K8094 below for digital storage and playback of short announcements and ID’s! In addition to the line level inputs, there is a separate front panel microphone input.
All three inputs have independent level controls eliminating the need for a separate audio mixer!
Just pot-up the source control when ready, and cross fade to the 2nd line input or mic! It’s that
simple! In addition to the dual stereo line inputs, a stereo monitor output is provided. This is perfect to drive
studio monitors or local in-house PA systems. The FM100B series includes an attractive metal case, whip antenna and built in 110/220VAC power supply. A BNC connector is also provided for an external antenna. Check
out our Tru-Match FM antenna kit, for the perfect mate to the FM100B transmitter. We also offer a high power
kit as well as an export-only assembled version that provides a variable RF output power up to 1 watt. The 1
watt unit must utilize an external antenna properly matched to the operating frequency to maintain a proper
VSWR to protect the transmitter.
(Note: The FM100B and FM100BEX are do-it-yourself learning kits that you assemble. The end user is responsible for complying with all FCC
rules & regulations within the US or any regulations of their respective governing body. The FM100BWT is for export use and can only be
shipped to locations outside the continental US, valid APO/FPO addresses or valid customs brokers for documented end delivery outside the
✔ PLL synthesized for drift-free operation
✔ Built-in mixer - 2 line inputs and one microphone
input, line level monitor output!
✔ Frequency range 88.0 to 108.0, 100 kHz steps
✔ Precision active low-pass “brick wall” audio filter!
✔ Dual LED bar graph audio level meters!
✔ Automatic adjustable microphone ducking!
✔ Easy to build through-hole design!
FM100B Super-Pro FM Stereo Radio Station Kit, 5u W to 25m W Output $239.95
FM100BEX Super-Pro FM Stereo Radio Station Kit, 5u W to 1W Output $299.95
Super-Pro FM Stereo Radio Station
Entry Test Set
Just like the days of "plugs,
points, and condenser" are
over, so are the days of having
the hardware store grind
out a spare key for your
Now when your keyless
access system doesn't work,
you need to accurately detect what part of the system
is malfunctioning. This could be anything from a dead
battery in the key fob, a "brain-dead" key fob, to malfunctioning sensors, antennas, or other system components in the vehicle. Until now there was no way to
determine where the system was failing.
Testing your system is easy. To test the complete 125
kHz/315 MHz communications path just stand close to
the vehicle with the WCT3 and your key fob in hand.
Press the test button and the WCT3 will detect and
display the presence of the vehicle's 125kHz/20KHz
signal and, if they "handshake", will also detect and
display the presence of your key fob's 315MHz return
signal. You can independently test key fob only signals (panic, lock, trunk, etc.) by holding the key fob
near the WCT3, pressing the test button, and pushing
the function button on the key fob.
The same functionality testing can be done with IR key
fobs. The modulated IR signal is detected and will
illuminate the IR test LED on the test set.
If you know a few "secrets" you can also see if the tire
pressure sensors/transmitters are generating signals or
the built-in garage door opener in your rear view mirror is transmitting a signal! Runs on a standard 9V
battery. Also available factory assembled & tested.
WCT3 Keyless Entry Test Set Kit $59.95
LTS1 Laser Trip Sensor Alarm Kit $29.95