Project
Figure 15. Heatshrinking provides a clean look.
Figure 16. Jumper locations for the switches and keypad.
Jumper 2
N5 ————————— E5
N6 ————————— E6
Solder two wires to program switches N5 and N6.
Connect the other end to a female jumper, then to E5 and
E6. Double-check the placement of the leads.
Jumper 3
E3 ————————— N3
E4 ————————— N4
E3 ————————— P5
E4 ————————— P6
This is a unique jumper. Connect two wires to E3 and
two wires to E4. One of the wires on E3 will connect to N3
and the other to P5. Connect two wires to E4. One of the
wires on E4 will connect to N4 and the other to P6.
Jumper 4
Q5 ————————— K2
Q6 ————————— K1
other end to the female jumper and then connect it to H1
and H2. Polarity is not important.
This is a simple female jumper to female jumper configuration. This jumper provides power to the controller
board.
Parts List
E
l
e
c
t
r
o
n
i
c
s
NUTS & VOLTS
F
o
r
E
v
e
r
y
t
h
i
n
g
Qty
1
1
1
1
Description
Dios 40-pin Microcontroller
Dios 28-pin Microcontroller
Dios Universal LCD Carrier
Crystalfontz Graphic LCD
1
1
2
Universal LCD Carrier Mounting Hardware
Dios Utility Carrier
1/8-inch Panels, 4 x 7 or 5 x 7 inches
2
Three-inch Handles
2
1
Miniature DPDT Three-position Switches
Miniature SPDT Switch
1
Matrix Keypad
4
2
8
4
2
1
5
1
Aluminum Spacers 4-40 Threads F-F
Aluminum Spacers 4-40 Threads M-F
4-40 1/2-inch Machine Screws
Rubber Feet
36-Pin Female Headers (Snapable)
Hookup Wire ( 10 feet Ribbon Cable)
1/16-inch Heatshrink Strips
Dios Compiler
1
AC Adapter 7-12V
Source and part number
Kronos Robotics #16168
Kronos Robotics #16169
Kronos Robotics #16410
CFAG12864B-YYH-V or
CFAG12864B-TMI-V
Kronos Robotics #16430
Kronos Robotics #16431
Expanded PVC 5 x 7 inch black
Kronos Robotics #16432 or
Plexi-Glass or equivalent from local
home center
Jameco #216821 or All Electronics
# HDL- 32 or three-inch cabinet handles
from local home center
Circuit Specialists #8012
Kronos Robotics #16241 or
All Electronics #MTS- 4
All Electronics #KP- 26 or #KP- 28 or
Circuit Specialists #KIT A1
Jameco #139205
Jameco #139213
Jameco #106809
Jameco #119618
Kronos Robotics #16291
Jameco #112547
Kronos Robotics #16287
Free download from Kronos
Robotics website at www.kronos
robotics.com
Kronos Robotics #16305
or any AC adapter with 2.1 ID and 2.5
OD center positive.
Jumper 5
D1 and D2 ————————— J1
Here, we take a two-pin
female header and short the two
leads together. Then, connect it
to a single female jumper with
one wire. This allows us to both
short the jumper (enable the
RS232 Reset) and route the reset
to the controller board at the
same time.
Jumper 6
N1 ————————— J3
N2 ————————— J2
Solder two wires to the program switch, then to a two-pin
female header. This is the pro-gram/debug port for the controller board J3 and J2.
Jumper 7
P3 ————————— E1
P4 ————————— E2
56
Solder two wires to the UART
switch and then to a two-pin
JULY 2005